HP Designjet Z2600 and Designjet Z5600 Error Code List

System Error: 01.0:YZ
Problem Description: Communication with Engine PCA failed
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the
power cord and power on the product.
2. Remove the Formatter and reinsert it again. Ensure that it connects properly in the Engine PCA
connector.
– Replace the Engine PCA. See EE Box
– Replace the Formatter. See Formatter
NOTE: For Revision B printers the Formatter and Hard Disk are replaced as a single part,

System Error: 01.1:YZ
Problem Description: Error in the Engine PCA
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the
power cord and power on the product.
2. Replace the Engine PCA. See EE Box
3. Replace the Formatter. See Formatter
NOTE: For Revision B printers the Formatter and Hard Disk are replaced as a single part

System Error: 01.2:YZ
For HP-authorized personnel only
Problem Description: Failure communicating with an Ink Supply
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Perform the Ink Delivery System diagnostic test. See Ink Delivery System (IDS) Test
– If the test ƭnds that the ink supply is defective, replace it.
– If the test does not ƭnd any errors, remove all the ink supplies from the ISS and reboot the product.
3. Install the ink cartridges with the product booted in normal mode. Use the replacement option
available from the Touch Control Panel and install the cartridges one by one. If an error appears
after installing a supply, the last supply you installed is defective. Replace it.
4. Check that the cables between the Left Ink Supply Station and the Engine PCA are not damaged
and are correctly connected. In case of any damage replace the cables; see Connecting the Data
Harness and ISS Harness Cable
5. Replace the Left Ink Supply Station. See Left Ink Supply Station
6. Replace the Engine PCA. See EE Box

System Error: 02.1:YZ
Problem Description: Problem with the Carriage PCA
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the
power cord and power on the product.
2. Check that the Trailing Cable is not damaged. Check that the Trailing Cable is correctly connected
between the Engine PCA and Carriage PCA.
3. Replace the Carriage PCA. See Carriage PCA
4. Replace the Trailing Cable and Carriage PCA Covers.
5. Replace the Engine PCA. See EE Box

System Error: 03:YZ (03:10)
Problem Description: Problem with Power Supply Unit
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Replace the Power Supply Unit (PSU). See Power Supply Unit

System Error: 03.0:10
Problem Description: Battery of Real Time Clock ran down
Corrective action: Replace the battery. See Real-time Clock Battery

System Error: 06:YZ
Problem Description: Failure reading/writing NVM in Hard disk
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Replace the Hard Disk. See Hard Disk Drive
NOTE: For Revision B printers the Formatter and Hard Disk are replaced as a single part

System Error: 07:10
Problem Description: Interconnect Board or Power cable has failed
Corrective action: Try the following:
1. Check the condition and connections of the Power Cable, replace if necessary.
2. Replace the Interconnect Board, , see Interconnect PCA

System Error: 07.01:11
Problem Description: DelSol3 ASIC not found or not responding
Corrective action: Try the following:
▲ Check the condition and connections of the Interconnect data and power cable, replace if necessary

System Error: 07.02:11
Problem Description: USB Cable not connected
Corrective action: Try the following:
▲ Check the condition and connections of the USB cable, replace if necessary.

System Error: 07.03:10
Problem Description: USB Hub not found
Corrective action: Try the following:
1. Make sure Interconnect board connector labeled 'INPUT HUB' is properly connected.
2. Make sure Wukong board connector labeled JUSB2 is properly connected to the cable coming from Interconnect board.
3. If failure continues, troubleshoot the error by changing the USB cable from Engine PCA to Interconnect, if the error follows to the changed part the USB cable is faulty, if it does not, the part is faulty.
4. Replace the Interconnect PCA, see Interconnect PCA
5. Replace the Formatter Board see Formatter
NOTE: For Revision B printers the Formatter and Hard Disk are replaced as a single part
6. Replace the Engine PCA see EE Box

System Error: 07.03:11
Problem Description: USB Scanner connected to incorrect port
Corrective action: Ensure that the USB cable from the Scanner to the Interconnect board is connected at the connection
labeled 'SCANNER' and not 'HOST CON'

System Error: 08:04

Problem Description: Communication with the Touch Control Panel is lost during normal printer operation or initialization.
Corrective action: Try the following:
1. Reseat the USB connectors on the interconnect PCA and on the engine PCA. 
2. Reseat printer’s formatter (do this by loosening the Formatter screws, disconnecting and reconnecting the Formatter, and tightening the screws again).
3. Check with the customer if another error appears on the Touch Panel before 08:04 (for example, 21: YZ or 22: YZ). In that case, follow the respective troubleshooting of that speciƭc error before continuing with these troubleshooting steps.
Check the event log in the EWS support pages, if accessible, to see if there is another SE (for instance, 07:10), and in that case, follow that SE’s troubleshooting process as well.
4. Perform an Emergency FW Upgrade using a USB flash drive, see Appendix B: Emergency firmware upgrade with USB flash drive
5. Remove the Ink cartridges, the LAN Cable, any media that is loaded, and the printheads if possible.
6. If the printer comes to Ready, Empty the Job queue.
7. Perform an EEROM reset from Diagnostic Mode if possible.
8. Check the USB cable connections from the Engine PCA to the Interconnect PCAs.
9. Check the connections of the Front Panel USB and Data cables.
10. Replace the cable running from the Engine PCA to the Interconnect PCA and from the FP to the
Interconnect PCA. It is included in the Interconnect Cable Kit.
11. Replace the Formatter Board
NOTE:
– For Revision A printers, never replace the Formatter and the Hard Disk at the same time.
Once the HDD is installed in one printer and it boots up, it cannot be used in another printer.
– For Revision B printers the Formatter and Hard Disk are replaced as a single part,
12. Replace the HDD, see Hard Disk Drive
NOTE:
– For Revision A printers, never replace the Formatter and the Hard Disk at the same time.
– For Revision B printers the Formatter and Hard Disk are replaced as a single part,
13. Replace the Interconnect PCA, see Interconnect PCA 
14. Replace the Touch Control Panel, see Touch Control Panel
15. Replace the Engine PCA; see EE Box 
16. Get the Extended Diagnostics Package and escalate the case for more help. 

System Error: 08:08
Problem Description: A feature on the Touch Control Panel hangs or will not function (copy,scan etc)
Corrective action: Try the following:
1. Turn oƫ the product and turn on again, and check to see if the error remains.
2. Upgrade the ƭrmware For more information, see Appendix B: Emergency ƭrmware upgrade with USB flash drive

System Error: 08:11
Problem Description: Communication lost between the Touch Panel and the printer.
Corrective action: Try the following:
1. Ask the customer to power off the printer, wait one minute and power it back on.
2. Reseat the printer’s formatter (do this by loosening the Formatter screws, disconnecting and
reconnecting the Formatter, and tightening the screws again).
3. Upgrade the ƭrmware (but, if booting up process is frozen at 1% please skip this step); see
Appendix B: Emergency ƭrmware upgrade with USB flash drive
4. Check the Formatter LEDs and perform the appropriate troubleshooting. See Troubleshooting
System Error 08:11 using the Formatter LEDs
5. Get the Extended Diagnostics Package and escalate the case for more help. 

System Error: 08:01:11
Problem Description: Touch Control Panel USB Cable fails
Corrective action: Try the following:
1. Check the condition and connections of the Touch Control Panel USB cable, replace if necessary.
2. If the error continues, replace the Touch Control Panel Touch Control Panel 

System Error: 09:01
Problem Description: Media jam in Scanner
Corrective action: Try the following:
1. Turn off the product using the Power key at the front, then also turn off the power switch at the rear and disconnect the power cable.
2. There is a small lever at the rear left of the scanner. Slide the lever to the right and open the scanner cover.
3. Solve the media jam.
4. Check and clean the pressure rollers.
5. Close the scanner cover and gently push it down to lock it into place.
6. Reconnect the product's power cable; turn on the power switch at the rear, and turn on the product using the Power key. If no paper is seen:
a. Open the scanner cover. Underneath you should see red flashing lights, then green, then blue.
b. In the center of the scanner cover, between the flashing lights, you will ƭnd 4 small sensors labeled as R, G, B and L. Put your ƭngers over the R, G and B sensors simultaneously and the scanner motor should advance.
c. If there is no response from the scanner motor, replace the Engine PCA, see EE Box

System Error: 09:02
Problem Description: Scanner not calibrated
Corrective action: Calibrate the Scanner Calibrate the Scanner

System Error: 09:03
Problem Description: File I/O Error
Corrective action: 1. Reboot Product.
2. Upgrade the ƭrmware with the latest ƭrmware, for more information, see Appendix B: Emergency ƭrmware upgrade with USB flash drive
3. Go to Jobs > Options > Delete all queue scan jobs
4. Make sure the hard disk that is installed in the printer is the correct one for the product you are repairing.
5. Check and clean scanner elements.
6. Calibrate the Scanner Calibrate the Scanner
7. In some corner cases, the issue could be related to media movement. Replace Media Sensors
Scanner Exit Media Sensors (MFP only)

System Error: 09:04
Problem Description: Contex Library failed to load
Corrective action: 1. Reboot the Product
2. Upgrade the ƭrmware For more information, see Appendix B: Emergency ƭrmware upgrade with USB flash drive

System Error: 09.01:10
Problem Description: Scanner Motor is failing
Corrective action: Try the following:
1. Reboot the printer.
2. If system error persists, upgrade with the last ƭrmware version.
3. Open the scanner cover. Underneath you will see red flashing lights, then green, then blue.
4. In the center of the scanner cover, between the flashing lights, you will ƭnd 4 small sensors labeled as R, G, B and L. Put your ƭngers over the R, G and B sensors simultaneously and the scanner motor should advance.
5. If there is no response from the scanner motor, replace the Engine PCA
or Stepper motor see Scanner Motor Assembly (MFP only)
6. Replace the Scanner Controller Board, see Scanner Controller Board (MFP only)
7. Check the Scanner Controller board cable connections and replace the cables if required.
8. Replace Media Sensors, see Scanner Exit Media Sensors (MFP only) 

System Error: 09.02:10
Problem Description: CIS A Element is failing
Corrective action: 1. Replace CIS A Element CIS Element (MFP only)
2. Clean the scanner of dust and dirt and perform the Scanner Calibration Calibrate the Scanner
3. If the system error persists, upgrade with last ƭrmware version. 
4. Replace Scanner Controller Board (SCU), see Scanner Controller Board (MFP only) 

System Error: 09.03:10
Problem Description: CIS B Element is failing
Corrective action: 1. Replace CIS B Element CIS Element (MFP only) 
2. Clean the scanner of dust and dirt and perform the Scanner Calibration Calibrate the Scanner
3. If the system error persists, upgrade with last ƭrmware version. 
4. Replace Scanner Controller Board (SCU), see Scanner Controller Board (MFP only)

System Error: 09.04:10
Problem Description: CIS C Element is failing
Corrective action: 1. Replace CIS C Element CIS Element (MFP only) 
2. Clean the scanner of dust and dirt and perform the Scanner Calibration Calibrate the Scanner
3. If the system error persists, upgrade with last ƭrmware version.
4. Replace Scanner Controller Board (SCU), see Scanner Controller Board (MFP only) 

System Error: 09.05:10
Problem Description: CIS D Element is failing
Corrective action: 1. Replace CIS D Element CIS Element (MFP only) 
2. Clean the scanner of dust and dirt and perform the Scanner Calibration Calibrate the Scanner
3. If the system error persists, upgrade with last ƭrmware version.
4. Replace Scanner Controller Board (SCU), see Scanner Controller Board (MFP only)

System Error: 09.06:10
Problem Description: CIS E Element is failing
Corrective action: 1. Replace CIS E Element CIS Element (MFP only) 
2. Clean the scanner of dust and dirt and perform the Scanner Calibration Calibrate the Scanner
3. If the system error persists, upgrade with last ƭrmware version. 
4. Replace Scanner Controller Board (SCU), see Scanner Controller Board (MFP only) 

System Error: 09.08:11
Problem Description: Power cable of the Scanner is failing
Corrective action: Check the condition and connections of the Scanner Power cable, if necessary replace the cable.

System Error: 09.09:11
Problem Description: USB cable of the Scanner is failing
Corrective action: Check the condition and connections of the Scanner USB cable, if necessary replace the cable.

System Error: 09.10:04
Problem Description: Scanner is in SAFE MODE
Corrective action: Restart the product, if the problem persists replace the SCU. See Scanner Controller Board (MFP only)

System Error: 09.10:10
Problem Description: Scanner Controller Board (SCU) is failing
Corrective action: 1. Turn off the product (20 sec.) using the Power key at the front, then also turn off the power
switch at the rear and disconnect the power cable.
2. Perform the Scanner Calibration Calibrate the Scanner
3. If the system error persists, upgrade with last ƭrmware version.
4. Perform File System Check; see File System Check
5. Perform the Scanner Validation; see Scanner Validation
6. Replace the Scanner SCU, see Scanner Controller Board (MFP only)
7. Check the Scanner USB cable connection and the Power/Reset/Awake cable from the Scanner
Controller Board to the Interconnect PCA and replaced if broken
8. Replace Interconnect PCA; see Interconnect PCA

System Error: 11:YZ
Problem Description: Trailing Cable does not seem to be detected
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the Trailing Cable is not damaged; replace it if necessary. Check that the Trailing Cable is correctly connected between the Engine PCA and Carriage PCA.
3. Replace the Carriage PCA. See Carriage PCA
4. Replace the Engine PCA. See EE Box

System Error: 21:YZ
Problem Description: Failure moving Service Station
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the product.
2. Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station.
3. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated. The cutter may be blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage.
4. Perform the Service Station diagnostic test to troubleshoot the problem further. See Service Station Test
5. Replace the Service Station. See Service Station

System Error: 21.1:YZ
Problem Description: Failure moving the Primer Motor of the Service Station
Corrective action: Try the following:
1. Remove the Right Cover and make sure the cables from the Engine PCA to the Service Station are connected and are not damaged. 
2. Perform the Primer Motor diagnostic test (listed under the service station diagnostic test) to troubleshoot the problem further. See Primer motor
3. Replace the Service Station. See Service Station

System Error: 21.2:YZ
Problem Description: Failure testing the length of the Service Station path
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the product.
2. Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station.
3. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated. It may happen that the cutter is blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage.
4. Perform the Service Station diagnostic test to troubleshoot the problem further. 
5. Replace the Service Station. 

System Error: 22.0:YZ
Problem Description: Left Ink Supply Station error, module 0.
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and are properly connected. In case of any damage replace the cable.
3. Perform the Ink Delivery System diagnostic test to troubleshoot the problem further.
4. Replace the Left Ink Supply Station. 
5. Replace the Engine PCA.

System Error: 22.1:YZ
Problem Description: Left Ink Supply Station error, module 1
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and
are properly connected. In case of any damage replace the cable.
NOTE: Check the Data Harness and ISS Harness Cable are connected in the right position onto
the Engine PCA. These two connectors can be swapped by mistake causing a SE 22.1:10. 
3. Perform the Ink Delivery System diagnostic test to troubleshoot the problem further. 
4. Replace the Left Ink Supply Station. 
5. Replace the Engine PCA. 

System Error: 24:YZ
Problem Description: Ink Setup failure
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Insert the new purgers, reconnect the power cord and power on the product.
2. Perform the Ink Delivery System diagnostic test in order to check that the bongos (pushers) go up and down to pressurize ink in the tubes and the Out of Ink sensors work properly. 
3. Try purging the Ink Supply Tubes again once the product has been restarted.
4. If the diagnostic test does not ƭnd any problem, install new cartridges in the product and try purging the Ink Supply Tubes again. It could be that one of the cartridges is defective.
5. If the problem persists, replace the Ink Supply Tubes. You must bring purgers and ink cartridges.

Warning: 26:01
Problem Description: Ink supply error found during IDS diagnostic test. In the Touch Control Panel message you will see
letters representing the names of the colors of the faulty supplies.
Corrective action: Try the following:
1. Reseat the faulty ink supply and repeat the Ink Delivery System diagnostic test.
2. If the problem persists, replace the faulty ink supply and repeat the Ink Delivery System
diagnostic test.
3. If the problem persists, replace the Left Ink Supply Station. 

Warning: 39.1:01
Problem Description: Roll 1 switch failed (standby or resume). Roll 1 has been unloaded.
Corrective action: There is no corrective action. This system warning code only notiƭies the user that the roll has been unloaded because an unexpected error occurred with Roll 1 in standby or resume operation.

Warning: 39.2:01
Problem Description: Roll 2 switch failed (standby or resume). Roll 2 has been unloaded.
Corrective action: There is no corrective action. This system warning code only notiƭies the user that the roll has been unloaded because an unexpected error occurred with Roll 2 in standby or resume operation.

System Error: 41:YZ
Problem Description: Electrical fault or current limit in Media-Axis Motor
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check for any visible obstacles restricting the movement of the Media Advance Roller. If there is a wrinkled mass of paper inside the paper path, lift the Pinch wheels (using Media Lever) and clear the obstruction.
3. Perform the Paper Drive diagnostic test to troubleshoot the problem furthe. 
4. Perform the Rewinder diagnostic test to troubleshoot the problem further. 
5. Check that the Media Advance Drive cable is not damaged and is correctly connected to the Engine PCA.
6. Replace the Media Advance Drive.
7. Replace the Engine PCA. 

System Error: 42:YZ
Problem Description: Electrical problem (fault, current limit, overheating) in Scan-Axis Motor
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check for any visible obstacles restricting the movement of the Carriage Assembly. Remove any obstacle to let the carriage move freely along the whole scan axis. If there is a wrinkled mass of paper inside the paper path, raise the pinch wheels (using the Media Lever) and clear the
obstruction.
3. Check that the Scan-Axis Motor cable is not damaged and is correctly connected to the Engine PCA.
4. Replace the Scan-Axis Motor. 
5. Replace the Engine PCA. 

System Error: 44:YZ
Problem Description: Aerosol fan fault
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the Aerosol Fan cable is not damaged and is correctly connected to the Engine PCA w/PSU SV.
3. Replace the Aerosol Fan Assembly. 
4. If the System Error continues, replace the Engine PCA. 

System Error: 45.1:YZ
Problem Description: An error with the Rewinder 1 System (Upper Rewinder) has been detected.
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Remove the paper from Roll 1. Reconnect the power cord and power on the product.
2. Check that the Rewinder 1 cable is not damaged and is correctly connected to the Engine PCA.
3. Check that the Upper Right Roll Support is correctly attached to and aligned with the Right Cover.
4. Perform the Rewinder diagnostic test to troubleshoot the problem further. 
5. Replace the Upper Right Roll Support. 

System Error: 45.2:YZ
Problem Description: An error with the Rewinder 2 System (Lower Rewinder) has been detected .
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Remove the paper from Roll 2. Reconnect the power cord and power on the product.
2. Check that the Rewinder 2 cable is not damaged and is correctly connected to the Engine PCA.
3. Check that the Lower Right Roll Support is correctly attached to and aligned with the Right Cover.
4. Perform the Rewinder diagnostic test to troubleshoot the problem further. 
5. Replace the Lower Right Roll Support. 

System Error: 47:YZ
Problem Description: Starwheels motor error
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check for any visible obstacles restricting the movement of the Starwheel Assembly, then clear the obstruction.
3. Check that the Starwheel Assembly cable is not damaged and is correctly connected to the Engine PCA.
4. Perform the Scan Axis Starwheel diagnostic test to troubleshoot the problem further.
5. Replace the Starwheel Motor. 
6. Replace the Engine PCA. 

System Error: 48:YZ
Problem Description: PPS system failure
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the Pen to Paper Space (PPS) Solenoid cable is not damaged and is correctly connected to the Engine PCA.
3. Perform the Scan Axis PRS diagnostic test to troubleshoot the problem further.
4. Replace the Pen to Paper Space (PPS) Solenoid. 
5. Replace the Engine PCA.

System Error: 51:YZ
Problem Description: Scanner Position Sensor failure
Corrective action: Try the following:
1. Check that the Scanner Position Sensor cable is not damaged and is correctly connected to the Engine PCA.
2. Perform the Sensors Test to troubleshoot the problem further. 
3. Replace the Scanner Position Sensor. 

System Error: 52:10
Problem Description: The product has detected a failure in the Drop Detector.
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the Drop Detector cable is not damaged and is correctly connected to the Engine PCA.
3. Replace the Drop Detector. 
4. Replace the Engine PCA. 

System Error: 55:YZ
Problem Description: Problem with the Line Sensor. The product has detected a failure to access the Line Sensor EEPROM.
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Perform the Carriage Test to troubleshoot the problem further. 
3. Check the Line Sensor connections to the Carriage PCA.
4. Replace the Line Sensor. 
5. Replace the Carriage PCA.

System Error: 56:YZ
Problem Description: Drive roller analog encoder homing (also known as “zero search”) failed.
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Perform the Media Path Test to troubleshoot the problem further. 
3. Replace the Encoder Disk and Encoder Sensor. 
4. Replace the Engine PCA. 

System Error: 59.1:09
Problem Description: Two electrical parts have been replaced at the same time.
Corrective action: Replace one part at a time, and restart the product before replacing another.

System Error: 59.2:00
Problem Description: An unsupported or reused part has been installed.
Corrective action: Install only new parts recommended by HP for this product.

System Error: 59.3:10
Problem Description: Wrong information stored on CryptoAsic
Corrective action: Call agent: Switch the power oƫ from the back of the product, wait two minutes, then switch it back on again.
Service engineer: Escalate the case to Level 3 requesting new CryptoAsic licenses.

Update theCryptoAsic with the delivered licenses.

System Error: 59.4:10
Problem Description: CryptoAsic failure
Corrective action: Call agent: Switch the power oƫ from the back of the product, wait two minutes, then switch it back on again.
Service engineer:
1. Reseat the CryptoAsic PCA.
2. Order a CryptoAsic PCA Service Kit and escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic PCA Service Kit.
3. Replace the CryptoAsic PCA. Write the ƭle provided by Level 3 to an empty USB, plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide the logs to Level 3.
4. Replace the Engine PCA. 

System Error: 59.5:19
Problem Description: CryptoAsic type missmatch
Corrective action: Call agent: Switch the power oƫ from the back of the product, wait two minutes, then switch it back on again.
Service engineer:
1. Reseat the CryptoAsic PCA.
2. Order a CryptoAsic PCA Service Kit and escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic PCA Service Kit.
3. Replace the CryptoAsic PCA. Write the ƭle provided by Level 3 to an empty USB, plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide the logs to Level 3.
4. Replace the Engine PCA.

System Error: 59.6:19
Problem Description: Printer serial number mismatch
Corrective action: Call agent: Switch the power off from the back of the product, wait two minutes, then switch it back on again.
Service engineer:
1. Reseat the CryptoAsic PCA.
2. Order a CryptoAsic PCA Service Kit and escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic PCA Service Kit.
3. Replace the CryptoAsic PCA. Write the ƭle provided by Level 3 to an empty USB, plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide the logs to Level 3.
4. Replace the Engine PCA.

System Error: 59.7:194
Problem Description: CryptoAsic generic error
Corrective action: Call agent: Switch the power oƫ from the back of the product, wait two minutes, then switch it back on again.
Service engineer:
1. Reseat the CryptoAsic PCA.
2. Order a CryptoAsic PCA Service Kit and escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic PCA Service Kit.
3. Replace the CryptoAsic PCA. Write the ƭle provided by Level 3 to an empty USB, plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide the logs to Level 3.

System Error: 60.1:YZ, 60.2:YZ
Problem Description: Initialization error
Corrective action: Try the following:
1. Switch the power off from the back of the product, wait two minutes, then switch it back on again.
2. Check the power cord; try connecting it to another power socket.
3. Check that the product is properly connected in all other respects.
4. Switch the power oƫ from the back of the product; remove the Formatter; reinsert the Formatter; switch the power on again.
5. If the error persists, get the product log and contact HP

System Error: 61:YZ
Problem Description: The file format is incorrect or not supported for the current product configuration and the product cannot process the job.
Corrective action: Try the following:
1. Check if the product supports the file format (formats such as PS, PDF, TIFF and JPEG are supported by PostScript products only).
2. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
3. Check the graphic language setting of the product (refer to the User's Guide).
4. Resend the file to the product.
5. Check that the product has the latest firmware version. If not, update the firmware to the latest version.

System Error: 61:04.1
Problem Description: The PostScript fonts seem to be missing.
Corrective action: Perform a firmware upgrade to re-install the fonts.

System Error: 61:08.1
Problem Description: The file cannot be printed because it is password-protected.
Corrective action: Resend the file without password protection.

System Error: 63:01
Problem Description: Cannot retrieve IP addess
Corrective action: Try the following:
1. Connect to another network.
2. Modify the IPv4 conƭguration.

System Error: 63:YZ
Problem Description: Input/Output problem through the network interface of the Formatter
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the Network cable is correctly connected to the Formatter.
3. Check that the product has the latest firmware version. If not, update the firmware to the latest version.
4. Replace the Formatter. 

System Error: 64:YZ
Problem Description: Input/Output problem through the USB Port
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the USB cable is correctly connected to the product.
3. Check that the product has the latest ƭrmware version. If not, update the firmware to the latest version.
4. Replace the Formatter. 

System Error: 64.1:YZ
Problem Description: The External Hard Disk accessory does not seem to be connected
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product. Connect the External Hard Disk accessory, check that the USB cable is properly connected and power on the product. If the External Hard Disk accessory is not available (has been lost or broken), proceed with step 2.
2. If the problem persists, power oƫ from the back of the product. Power on the product again while pressing the keys Menu, OK and Cancel keys simultaneously until the Touch Control Panel asks “product conƭgured to use External Hard Disk. Do you want to revert the product to Internal Hard
Disk?” Conƭrm by pressing OK (twice). Remove the External Hard Disk accessory (if connected).
The product will restart.
3. After the product reaches the Ready state, try connecting any other USB device (known to work properly) to the product port where the External Hard Disk accessory should be connected.
– If a message appears on the Touch Control Panel reacting to the USB device just connected (such as “Please remove USB device” or “Press on this menu option...”), press Cancel and remove the USB Device. This means that the External Hard Disk accessory is faulty and
should be replaced – If nothing appears on the Touch Control Panel reacting to the USB device just connected, the Formatter is faulty and should be replaced. 

System Error: 65:YZ
Problem Description: Memory Driver Internal I/O error, I/O Socket Manager Internal I/O error
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the unknown port cable is correctly connected to the product.
3. Check that the product has the latest firmware version. If not, update the firmware to the latest version.
4. Replace the Formatter. 
5. Replace the Engine PCA. 

Warning: 68:YZ
Problem Description: Loss of engine counters tracking
Corrective action: The product will continue to function correctly, but the life counters will not continue counting until you restart the product.

System Error: 71:03
Problem Description: Out of memory
Corrective action: Restart the product.

Warning: 71:04
Problem Description: Out of memory.
The total memory available in the product depends on its configuration. It is reported as HP-GL/2 memory or PS/PDF memory. If the amount of memory that the product needs to process the file is more than the amount available, the product will display this system warning. The amount of memory required for processing the file is known as the ‘display list memory’:
● The display list memory should not be confused with the file size of the print job. The size of the display list memory depends on several variables such as the resolution, file size and file content.
● The display list memory is not visible to the user, but can be consulted by engineers to troubleshoot out-of-memory issues.
● There have been a few cases in which a print job with a relatively small ƭle size has triggered an
out-of-memory message. Such print jobs typically have a large number of objects in them or
have complex objects such as raster images with gradients or objects with multiple layers.
Corrective action: Try the following:
1. Upgrade the ƭrmware to the latest version available.
2. Decrease the print resolution to 300 dpi.
NOTE: If the customer does not accept the print quality after reducing the resolution or using
Econofast print mode, proceed to the workaround in step 3.
– The resolution required by the product to process the ƭle is set by the print mode selected
(Best, Normal, Fast). There is a setting available that enables you to decrease the resolution
for each print mode to 300 dpi. If this setting is used, the rendering resolution will be
reduced, but the output (printing) resolution will remain the default of the selected print
mode. There could be an impact on Image Quality because of the reduction in the rendering
resolution; this will be especially noticeable in circles and lines with very low inclination.
For HP-authorized personnel only
ENWW System Error Codes—Full Descriptions 99
3. Use the ‘Econofast’ print mode. The rendering resolution will be set by default to 300 dpi. In the
Paper/Quality tab of the product properties window, select Custom options and press the
Settings button. In the Custom Print Quality Options window, check the Economode box.
NOTE: If the Out of Memory message still persists, proceed to the next workaround.
4. Out of Memory issues can always be solved if the processing of the job can be performed before
reaching the product. This can be done by selecting ‘Send Job as Bitmap’. The main processing of
the print job will then be performed by the computer. This form of printing is recommended when
the print job contains raster images, and mixed plots with raster images and lines, because the
process of turning a print job made of raster images to vector images leads to a signiƭcant
increase in the display list memory.
Warning: 72.02:09
For HP-authorized personnel only
100 Chapter 2 System Error Codes ENWW
Problem Description: Generic ƭrmware Error
Corrective action: 1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the
power cord and power on the product.
2. Check that the product has the latest firmware version. If not, update the firmware to the latest version 
NOTE: If you see system error 79:04, a firmware upgrade will not always solve the problem. The best way to solve this problem is to email Tim at sales@lpscomputer.com, and he will help you diagnose the root cause. 

Warning: 72.02:YZ
Problem Description: A service calibration should be performed.
Corrective action: To find out which service calibration to perform, print the calibration status. At the Touch Control Panel, select the Internal Prints icon, then Service information > Print calibration status. Perform whichever calibration is needed.

Warning: 74:YZ
Problem Description: Error uploading firmware update file
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Make sure the connection between the computer and the product is functioning properly.
3. Try to update the firmware again.

Warning: 74.1:YZ
Problem Description: Error uploading paper update file
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Make sure the connection between the computer and the product is functioning properly.
3. Try to upload the paper proƭle update ƭle again.
4. Make sure the version of the paper proƭle update ƭle is compatible with the ƭrmware version the product is using. You can check this on the same Web page where you downloaded the paper proƭle update.

System Error: 74.08:04
Problem Description: Problem with the firmware upgrade process
Corrective action:

1. Reboot the Product
2. Try to upgrade the firmware again
3. Download again the firmware file from the source, as the original may be corrupted.
4. Replace the Touch Control Panel

System Error: 75.21:YZ
Problem Description: The spittoons (Left Spittoon, Service Station) have reached 80% capacity.
Corrective action: Use Preventive Maintenance Kit #2 to replace the Service Station.

System Error: 75.22:YZ
Problem Description: The spittoons (Left Spittoon, Service Station) are full.
Corrective action: Use Preventive Maintenance Kit #2 to replace the Left Spittoon and Service Station.

System Error: 76:YZ
Problem Description: Hard disk drive is full.
Corrective action: Remove any unnecessary files from the hard disk using the Embedded Web Server. If the problem persists, run the Hard Disk Recovery Utility 

System Error: 78:08
Problem Description: The job received cannot be printed without borders on this paper.
Corrective action: Use a paper that supports borderless printing.
NOTE: This system error code does not require service help. It should be resolved by the customer.

System Error: 78.1:YZ
Problem Description: Media settings area missing in paper settings ƭle
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the product has the latest firmware version. If not, update the firmware to the latest version.

System Error: 79:YZ

Problem Description: Generic error
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Check that the product has the latest firmware version. If not, update the firmware to the latest version.

NOTE: A firmware upgrade will not always solve the problem. The best way to solve this problem is to report the error to Tim at sales@lpscomputer.com. Make sure that you supply all the information accessed by pressing on the bottom right area of the touchscreen (same place where the cancel icon usually shows)

System Error: 81:01
Problem Description: Paper axis error—the copier will restart and run a diagnostic test
Corrective action: None

System Error: 81:YZ
Initial checks: This error can occur because the product has been dropped during transportation, causing structural damage. Before continuing with the 81:YZ troubleshooting, first look for structural damage.
To identify the structural damage, look for the following three things:

● Consistent 81:YZ error codes.
● Platen fingers rubbing on the roller surface, leaving black marks on the roller.
● A gap on the platen beam. If there’s any gap in Z (vertical direction) between the plastic feature of the platen and the metal side plate, then the chassis is damaged and the unit cannot be repaired.

Problem Description:
Problem with paper advance. This source of error could come from an error in any of the following systems: paper motor, disk encoder, cables or main electronics.
Corrective action:
Try the following:
1. Check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of paper inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction.
2. Perform the Media Drive diagnostic test to troubleshoot the problem further. 
3. Perform the Rewinder diagnostic test to troubleshoot the problem further. 
4. Check the connections on the Engine PCA; the Media Advance Drive is connected to the connector labeled Paper Motor.
5. Adjust the encoder disc and motor mount configuration using the Media Advance Drive installation instructions.
6. Replace the Media Advance Drive. 

System Error: 86:01 (or 86:11)
Problem Description: Scan Axis movement requires too much force or energy.
Corrective action:

1. Check that the cutter disengages correctly.
2. Lubricate the scan axis.
3. Email Tim at sales@lpscomputer.com

System Error: 87:YZ
Problem Description: Problem with the Carriage Encoder Sensor readings
Corrective action: Try the following:
1. Check that the encoder sensor is correctly connected to the Carriage PCA.
2. Make sure the Encoder Strip is not broken or damaged. If necessary, replace it.
3. Make sure that the Encoder Strip is clean. If it is dirty, clean it, paying special attention to the area near the Service Station.
4. Clean the Encoder Sensor.
5. Replace the Encoder Sensor.
6. Replace the Carriage PCA. 
7. Replace the Trailing Cables. 

System Error: 87.01
Problem Description: Problem finding the Scan-axis encoder reading
Corrective action: Try the following:
1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Make sure that the encoder strip is clean. If the encoder strip is dirty, clean it, paying special attention to the area near the Service Station.
3. Clean the encoder sensor.
4. Replace the Encoder Sensor.

System Error: 93:YZ
Problem Description: Unable to pressurize the Ink Delivery System
Corrective action: Try the following:
1. Switch the power oƫ from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
2. Perform the Ink Delivery System diagnostic test to further troubleshoot the problem.
3. Check that the cables between the Ink Supply Station and the Engine PCA are not damaged and are properly connected. In case of any damage replace the cable.
4. Replace the Left Ink Supply Station, depending on the results of the diagnostic test. 
5. Replace the Engine PCA. 

How to troubleshoot SE 79:04

The system error 79:04 is a generic error (equivalent to a blue screen in windows). It’s the system error that the product will display when an unknown exception occurs that cannot be identified as relating to any specific subsystem of the product.

Since this is a generic error, there can be multiple causes behind it. This document will cover the most probable causes behind a system error 79:04 and will recommend the most efficient troubleshooting steps to resolve customer issues.

It is important to mention that, although 79:04 system errors can be caused by a hardware malfunction, the vast majority of 79:04 system errors are pure software or firmware issues. Before doing anything else, you are recommended to try the following general-purpose solutions.

1. Update the product’s firmware to the very latest available firmware version, even if the product appears to be running the latest firmware already.
2. Restore the factory settings from the Touch Screen Panel's Setup menu.
If these do not solve the problem, continue reading about other possible solutions below.

Possible causes
Since the 79:04 system error is a generic error, the number of possible causes behind it is large. The majority can be grouped, however, into the following groups.

Job-related SE79:04
A specific print job that is not correctly formatted for the product or that is not correctly processed by it can trigger a 79:04 system error.
The incorrect format or processing can come from two sources:
● Incorrect commands in the job itself. For example, a PS job with some commands that do not have the correct PS format.
● Issues applying to the settings in the job
Possible symptoms

79:04 caused by a print job always have the same symptoms:
1. The job is received by the product and starts to process.
2. In the middle of the processing, the product stops and displays 79:04.
3. The product will display the 79:04 system error again after reboot. This is due to the fact that the product will try to reprint the job, which is pending in the queue, after reboot.
4. After the second reboot, the product will start up normally
5. If the same job is sent again, it will always produce a 79:04 system error
These types of 79:04 system errors are normally caused by jobs that have been generated by 3rd party applications (RIPs, 3rd party drivers, files exported by an application to PS, PDF, HP-GL/2, RTL, … or any other format supported by the product). Jobs generated by HP drivers will not normally generate 79:04